公司新聞
壓路機啟動很困難的原因有什么？
來源：http://www.yuanchuodian.cn/ 日期：2022-04-20
壓路機作為一種用于建筑施工的大型設備，使用起來要小心才是，表現為操作正確以及多注意一些事項，不過使用時間久了就會出現故障，比如說不能啟動或者啟動很困難，原因是什么呢？
Roller as a large equipment for construction, use should be careful, performance is correct operation and pay more attention to some matters, but the use of a long time will fail, such as can not start or start is very difficult, what is the reason?
蓄電池電壓過低或兩級夾子松動氧化，造成起動機轉動過慢。隨著溫度下降（尤其是超過2年），電池本身的存儲容量會下降。在這種情況下，需要及時更換。在冬季低溫劣質柴油的情況下，油中的雜質低于標準純度，導致供油不足，供油系統堵塞管道。在這種情況下，只需減少燃油即可添加優質柴油。釋放出來的油在夏天仍然可以使用。
Battery voltage is too low or two stage clamp loose oxidation, resulting in slow rotation starter. As the temperature drops (especially over 2 years), the storage capacity of the battery itself decreases. In this case, timely replacement is required. In the case of low temperature and inferior diesel oil in winter, the impurities in the oil are lower than the standard purity, leading to insufficient oil supply, oil supply system blockage pipeline. In this case, just reduce the fuel and add premium diesel. The released oil can still be used in the summer.
不能調節油門桿，使供油量過高，或供油量不足，使最小的振動壓路機難以啟動。檢查油門桿固件是否完好，拆解后油門拉線是否可以拆下。如果可以拉動但不能彈跳，則可能需要更換油門拉線。
Cannot adjust the throttle rod, so that the fuel supply is too high, or insufficient, so that the smallest vibration roller difficult to start. Check whether the throttle rod firmware is intact and whether the throttle cable can be removed after disassembling. If you can pull but cannot bounce, you may need to replace the throttle cord.
出廠時防凍液的比例為50%，可調節至-40度低溫。如果啟動困難，首先檢查防凍液液位和油位，看是否是漏油或防凍液不足造成的。如果氣門間隙過小，可能造成漏氣、斷電、氣門密封面密封嚴重、積碳，甚至氣門撞到活塞。間隙過大將導致發動機進氣不足、排氣臟污和功率降低。不正確的氣門間隙尺寸也會使小的振動壓路機難以啟動，因此您需要對其進行檢查。
Factory antifreeze ratio is 50%, adjustable to -40 degrees low temperature. If it is difficult to start, first check the antifreeze level and oil level to see if it is caused by oil leakage or lack of antifreeze. If the valve clearance is too small, it may cause air leakage, power failure, severe sealing of valve sealing surface, carbon accumulation, and even valve bumping into the piston. Too large clearance will lead to insufficient engine air intake, dirty exhaust and reduced power. Incorrect valve clearance sizes can also make it difficult to start small vibratory rollers, so you need to check them.
濟南壓路機租賃廠家提醒大家，如果不想自己的壓路機在使用過程中突然的出現類似于不能啟動或啟動很困難等問題，就要在平常中多多去了解相關的注意事項，以及正確的操作方式。當然使用壓路機工作前后期間也不能大意，必要的檢查是需要的。
Ji 'nan roller rental manufacturers remind you that if you do not want to use their roller in the process of sudden emergence similar to can not start or start is very difficult and other problems, it is necessary to understand the relevant matters needing attention in the ordinary, and the correct way of operation. Of course, the use of roller before and after the work period can not be careless, the necessary inspection is needed.
壓路機啟動很困難的原因有什么？以上便是問題的相關解答了，如果您對此有什么疑問的話，可以隨時來我們網站www.yuanchuodian.cn咨詢，專業人員會根據實際問題進行具體的分析。
What makes it difficult to start a roller? The above is the relevant answer to the question, if you have any questions about this, you can come to our website www.yuanchuodian.cn at any time to consult, professionals will carry out specific analysis according to the actual problem.
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：